How to Replace the Headlights on a 2014 Jeep Grand Cherokee: A Quick and Easy Guide
The headlights are probably the most important feature on your vehicle when driving at night. They light up the road ahead and alert other drivers of your presence. If you notice that your headlights aren’t shining as bright as they once did, it’s time to get a new pair. You can purchase replacement headlight bulbs from almost any car parts store or auto repair shop. However, if you have a 2014 Jeep Grand Cherokee, things are slightly different than with other vehicles. The 2014 Jeep Grand Cherokee has an odd set-up for its headlamps and fog lights—they’re all in one housing unit called the “ illumination module .” It sounds complicated but rest assured it isn’t too hard to replace. Here is what you need to know about replacing the headlight bulbs on your 2014 Jeep Grand Cherokee.
How to Change the Headlight Bulbs on a 2014 Jeep Grand Cherokee
The first thing you’ll need to do is turn off the engine, and disconnect the negative battery cable from the battery terminal. The 2014 Jeep Grand Cherokee uses a different illumination module than most other vehicles, so you can’t just unscrew the bulbs like you could on non-Chrysler models. The bulbs have a “laser-guided” type socket that is specific to the Grand Cherokee. Because of this, you’ll need to remove the front bumper covers to get to the illumination module. Loosen the screws on each side of the grille, and pop out the covers. Now you can access the headlight and fog light bulbs, as well as the control module and high-beam indicator. The control module is mounted on the side of the engine compartment, and the high-beam indicator is mounted right above the fog lights. Replace the bulbs, put everything back together, and you’re done!
What You’ll Need
The only thing you really need to replace the headlight bulbs on your 2014 Jeep Grand Cherokee is a screwdriver. There are some extra things you can use, but they are not necessary. First, you’ll need to turn off the engine, and disconnect the negative battery cable from the battery terminal. Next, you’ll need to remove the front bumper covers and loosen the screws on each side of the grille. From there, you can access the headlight and fog light bulbs, as well as the control module and high-beam indicator. The control module is mounted on the side of the engine compartment, and the high-beam indicator is mounted right above the fog lights. You’ll also want to make sure you have a clean, dry work space. You never know when you might drop a tool, and if it gets wet, it could short out electrical components.
Step 1: Turn Off the Engine and Disconnect the Battery
The first thing you’ll need to do is turn off the engine, and disconnect the negative battery cable from the battery terminal. The Grand Cherokee uses a different illumination module than most other vehicles, so you can’t just unscrew the bulbs like you could on non-Chrysler models. The bulbs have a “laser-guided” type socket that is specific to the Grand Cherokee. Because of this, you’ll need to remove the front bumper covers to get to the illumination module. Loosen the screws on each side of the grille, and pop out the covers. Now you can access the headlight and fog light bulbs, as well as the control module and high-beam indicator. The control module is mounted on the side of the engine compartment, and the high-beam indicator is mounted right above the fog lights.
Step 2: Remove the Headlight Housing
To remove the headlight housing, you’ll need to remove the six mounting screws. There are two on the top, two on the bottom, one on the side by the wheel well, and one by the fog light. Once all six screws have been removed, you can pull the headlight housing out of the wheel well. You should now be able to access the high-beam indicator and control module. To remove the illumination module, you’ll need to unclip the wiring harness from the control module. There will be a small black clip on the side of the module that you’ll need to press in and pull out. Now you can remove the illumination module from the housing.
Step 3: Loosen and Remove the Headlight Housing
Once the housing is removed, there are two plastic clips on the back of the housing that you can loosen. These will release the light bulbs, as well as the back of the housing. Now you can remove the bulbs and replace them with new ones. The beam pattern on the 2014 Jeep Grand Cherokee is a little different than on other vehicles. The low beam is the inner bulb, while the high beam is the outer bulb. You can tell which is which by looking at the plastic lens covering each bulb. The low beam lens is clear, while the high beam lens has a “racing stripe” going down the middle. The lens screws off, and you can remove the old bulbs and replace them with new ones.
Step 4: Install the New Headlight Bulbs
Once the new bulbs are in place, you can put the housing back together. You can reattach the wiring harness clip to the control module. Once the housing is back in place, you can put the screws back in and tighten them down. Now you can put the bumper covers back on, and you’re finished! The Grand Cherokee uses a different illumination module than most other vehicles, so you can’t just unscrew the bulbs like you could on non-Chrysler models. The bulbs have a “laser-guided” type socket that is specific to the Grand Cherokee. The beam pattern on the 2014 Jeep Grand Cherokee is a little different than on other vehicles. The low beam is the inner bulb, while the high beam is the outer bulb. You can tell which is which by looking at the plastic lens covering each bulb. The low beam lens is clear, while the high beam lens has a “racing stripe” going down the middle. The lens screws off, and you can remove the old bulbs and replace them with new ones.